AMB-300 Addressable PIR Detector INSTALLATION INSTRUCTIONS The AMB-300 is a general purpose PIR detector designed to provide reliable motion detection for residential and commercial applications. Exceptional design care and factory testing ensure years of trouble free performance. The detectors provide immunity against false alarms from RF, static, electrical tran - sient and white light. Multi-level signal processing*, temperature compensation and a large multi-beam lens design means that the human target will not slip by unnoticed—even on a hot summer day. Four interchangeable lenses, wall or corner mounting and vertical adjustment provide application versatility.

Your client will appreciate the small size and elegant simplicity of the case design. The AMB-300 uses a 2-wire connection for power and to communicate with the con - trol panel. Serial number edius pro 7.2. This simplifies wiring and reduces installation cost. The AMB-300’s low cur - rent draw also maximizes the number of devices that can be attached to an addressable loop. Specifications • Current rating: 0.75 mA (standby); 3 mA (test mode) • Operating environment: 32°F-120°F / 0°C-49°C; 5%-93% RH, non-condensing • Radiated RF immunity: 10 V/m with 80% AM over range, 80MHz to 1.0GHz** • Conducted RF immunity: 10V with 80% AM over range 150kHz to 100MHz** • Static immunity: 15 kV • Transient immunity: 2.4 kV @ 1.2 joules • White light immunity: 20,000 Lux @ device • Walk detection speed: 0.5-10'/s (0.15-3m/s) • Coverage angle (BV-L1): 90° minimum • Vertical adjustment: +5° to -10° • Mounting heights: 6-10'/2-3m (nom. 7.5'/2.3m); 4-5'/1.2-1.5m (pet alley only) • Tamper switch contact rating: 0.1A @ 24V DC Control Panel Compatibllity • PC4010/4020 v3.x • PC5010/PC5015/PC5020 v2.x with PC5100 interface module ∗ Protected by one or more of the following patents: Canada 2099971, US 5444432 ** RF immunity and white light not verified by UL Beam Patterns for Lenses BV-L1 to BV-L4 Locating the Detector Select a detector location that will provide the coverage required keeping in mind the following potential problems.

Solve device problem. Videos (tutorials) Documents. REPLACE DSC MAXSYS PC4020 WITH NEWER VERSION PANEL. DIGITAL SECURITY CONTROLS DSC PC4108A. Check on Amazon. Installation of the DLS Software 2 - Dot Com Security Services. Maxsys4020CFv3 Spec Sheet - selectsecurity.net.

• Do not aim the detector at reflective surfaces such as mirrors or windows as this may distort the coverage pattern or reflect sunlight directly onto the detector. • Avoid locations that are subject to direct high air flow such as near an air duct out - let. • Do not locate the detector near sources of moisture (steam or oil). • Do not aim the detector such that it will receive direct or reflected (mirror) sunlight. • Do not limit the coverage by large obstructions within the detection area such as plants or filing cabinets.

• When using BV-L4 (Pet Alley lens): Do not aim the detector at a stairway which a pet has access to. Do not place furniture or objects higher than 3 ft/0.9 m, which a pet can climb onto (e.g. A cat on a couch), closer than 6 ft/1.8 m to the detector.

Mori seiki nv 5000. Equipped With: TRAVELS: --X: 31.5' --Y: 20.1' --Z: 20.1' PALLET CHANGER TABLE SIZE: 18.9' X 37.4' PALLET CHANGE TIME: 16.5 SEC.

Device Wiring To connect the AMB-300, consult the wiring diagram below: Mounting To open the case, use a small flat blade screwdriver and gently push in the tab at the bottom of the case and pull the cover straight out at the bottom. Loosen the printed circuit board screw, and push the board up as far as it will go. Using a small screw - driver, remove the appropriate knockouts for the mounting screws. Remove the desired wiring entrance knockouts located at the top or bottom of the backplate.